The Konig Elite Range is perfect for any project, from the busiest of homes to any commercial setting.
One of the hardest wearing floors on the market, the Konig Elite range offers customers the security of an AC5 rated,100% Waterproof floor, while still maintaining the look and feel of a real wood floor.
This versatile grey flooring will offer homeowners endless decor possibilities. it is extremely adaptable, and easily pairs with diverse colours, without losing that uniqueness.
The grey colours allows you to accomplish an airy atmosphere, and can make a smaller room look spacious
Is this floor hardwearing?
Yes, this floor has an AC5 rating, meaning it is suitable for commercial use
Do you need underlay with this product?
This range of floor comes with an underlay attached, so there is no need to purchase more underlay
What is this floor made of?
This range of flooring is made of Stone and PVC, making it extremely usable and 100% waterproof
How to take care of the floor?
We would recommend to clean this floor with a damp mop. no abrasive chemicals are recommended
Site Prep, Subfloor and Underlay
One of the most important stages to consider prior to laying any type of flooring installation is site prep.
Remove all furniture from the room, brush and vacuum the sub-floor.
When fitting any flooring a key factor in site preparation is ensuring the subfloor is level. Take time to look for any unevenness in the surface. This could be nails, lumps of concrete or generally anything that would obstruct the laminate from being laid perfectly flat. In some cases, levelling compound or sheets of plywood may be needed to achieve this. Also, test for dips or humps in the sub-floor using a long straight edge such as a spirit level. Place it in multiple areas of the room and get down low to look for any potential dips or humps. Anything over 2mm in a 1 metre run should be levelled out using a suitable floor levelling compound.
If you are laying onto a new concrete sub-floor, check that it is fully dried which can take anywhere from 2 - 4 months.
Most underlays are suitable to use with laminate flooring. When choosing your underlay, you may decide to go for a noise-reducing underlay, typical foam underlay or one suitable for underfloor heating.
Expansion Gaps
It is vital to leave a consistent expansion gap of 7-10mm at walls, pillars, stairs, doorways and other fixed objects or boarders in the room such as kitchen islands or fitted wardrobes. When drilling a hole for pipes, the hole should be 7-10mm larger than the pipe itself. Objects should not be fixed to a floating floor as this prevents the floor from expanding or contracting when needed.
Materials needed:
Tri square Tape measure
Spirit level
Ruler
Pencil
Saw or stanley knife 7 - 10 mm spacers Rubber mallet Underlay
Flooring Pencil
Installation Guidelines
*** These instructions are a guide only. If you are unsure about anything you should refer to the instructions provided with your materials. ***
• Start in a corner and work left to right. The end with a shorter tongue should be placed against the wall. 7 - 10mm expansion spacers should be used along the wall to maintain a consistent gap. The gap will allow for any natural expansion in the future that comes with changing seasons. Without this gap, you may encounter some issues with your laminate floor.
• The second board should be laid fitting the tongue and groove mechanisms together. It is always best to refer to the specific brand’s guidelines as these grooves differ between brands. Repeat this process until the end of the row.
• In the case that the last board of the row is too long, you will need to cut this down to fit with a saw. Remember to account for the expansion spacer in this measurement. Turn the board 180 degrees in order to measure accurately and lay next to the previous board laid. After cutting, place the board down with the cut side next to the wall.
• The typical design for laying wooden floors is to keep the ends of the boards approximately 30 cm apart. If the cut off board from the previous row is longer than 30cm, use this as the first board of the second row. The freshly cut side should always face the wall. However, if it’s too short, you can cut down another board to use instead. It is advised to keep a consistent length of 30cm between the ends of the boards in order to maintain this look.
• In most cases, you will need to fit long edges together at 30 degrees from the floor before lowering it and locking it in place. The boards should then slide together into place. This is only the case for most brands so the manufacturer’s guidelines should always be considered.
• If any last boards need to be cut lengthways, you can use another board to guide any markings needed before cutting.
• Assuming these guidelines are followed and the manufacturer’s instructions are studied accordingly, there should be no issues with laying a laminate floor.
• If you need any more assistance with this you can call our team on 01 840 4458 or email us at hello@woodfloorstore.ie.
Protection and Cleaning
Use wood flooring felt pads on heavy furniture and chairs that will be used frequently.
Check shoes, especially heels and football boots for any metal or hard materials that may damage your floor.
Install door mats at entrances to help remove any dirt, stones, and moisture from the bottom of shoes.
Heat should be maintained between 15- 28°C to avoid excessive movement.
Buy now,
